MD Activator No. 9 for CA adhesives

Cleans and degreases parts and accelerates the hardening of CA adhesives. Bonds within 1-4 seconds depending on the CA adhesive as well as the gap between the parts and the room temperature.

Art.-No. MAC.A9.Y150 | Packaging unit 6 spray tins á 150 ml

MD Primer No. 7

PP, PE, silicone and Teflon® cannot be bonded together without prior treatment. Bonding materials only with adhesive and not with a primer achieves adherence but no firm bonding. The primer permits polyolefins (polyethylene, polypropylene), PTFE, silicones and other difficult-to-bond materials to be bonded together.
 
Application:
Apply a thin layer of primer to the surfaces to be bonded and allow to dry for several seconds. Apply the adhesive and press the parts together. Bonds after 1-2 minutes. Final hardness is achieved after 24 hours.

Art.-No. MAC.P7.Y15 | Packaging unit 25 glass bottle with spray head  á 15 ml
Art.-No. MAC.P7.F15 | Packaging unit 25 glass bottle with brush á 15 ml

MD Hardening accelerant

Marston-Domsel’s hardening accelerant ensures even faster hardening of MG-GLUE instant adhesive. Mainly use for instant adhesives with higher viscosities.

Application:
Removes contamination and oil/grease from surfaces to be bonded using a product such as Marston Cleaner. Apply the MD-activator for CA by spraying it on to one surface to be bonded. Apply adhesive to the other side and press the parts together immediately.

Art.-No. MAC.Y15 | Packaging unit 25 glass bottles with spray head á 15 ml

MD GLUE Instant adhesive

There is no adhesive which can bond everything. Specific adhesives are necessary for various materials which are matched with them as regards their structural composition and in their viscosity.

MD instant adhesive by MARSTON-DOMSEL is supplied in practical bottles with droppers and is available in various versions for all kinds of materials.

• Economical in use
• Precise application possible
• High impact resistance
• Extremely high tensile strength
• High temperature stability
• Good water resistance for special types
• Bonds in a few seconds
• NSF Approval

Areas of application:

The electrical and electronics industries, engineering, metalworking, automotive construction, model construction, the furniture industry, plastics processing, dentistry, fingernail bonding, the rubber industry, the lighting industry etc.

Among other things, MOISTURE RESISTANT is moisture-resistant. Compared with a standard CA adhesive, it features excellent media resistance.

low viscosity

DUPLEX is characterised by the two different ways of curing – through UV light or humidity.  Thus, even non-transparent materials can be transparently bonded free of errors. Excess adhesive can be hardened in 1–2 s. It can also be used as a casting mass.

medium viscosity

HEAT is a high-temperature adhesive that can be used in all areas in which high temperatures are required. In this temperature range (up to 150°C), permanently achieving a firm bond is a novelty.

medium viscosity

MD GLUE FL
medium viscous

For transparent and translucent plastics. The
bonded location leaves no white edge and does
not effloresce.

MD GLUE SQ
medium viscous

For fast bonding
of plastic and
rubber.

MD GLUE Styro
medium viscous

Adhesive for
polystyrene.

UV-STAR - UV repair adhesive - Glue at the push of a button - Controlled hardening in just 3 seconds!

MD-UV-STAR special adhesive combines high strength with absolute reliability and virtual invisibility for glass / plastic / metal / wood / stone. It is suitable for bonding glass jewellery, lead crystal glass and laminated safety glass (e.g. automotive glazing and rear view mirrors). Not suitable for aquariums. The adhesive hardens by UV light using the enclosed UV projector or by itself in direct sunlight.

• Model building
• Glass n Wood
• Acrylic
• Porcelain
• Ceramics
• Jewellery
• Metals
• Rubber
• Plastics
• Insulation
• Automotive glazing
• Waterproofing

Bonding at the push of a button!

You choose at the push of a button:
When the adhesive reacts and bonds!
How quickly the adhesive reacts!
What the adhesive strength is!
How hard the adhesive is!
The elastically of the bond!

Find out more
1. You can use MD UV-STAR without hassle, without mixing and time pressure, to coat, seal, model or repair. You can apply, align, fix and if necessary remove any residue with ease. No problem.
2. MD UV-Star only reacts to form a solid plastic matrix once the button on the UV projector has been pushed.
Specific or large areas exactly where and when you want. If required in only a few seconds.

What is so special about MD UV-STAR?
1. You decide when and where by pressing a button, how quickly and how firmly UV-STAR reacts and hardens as an adhesive and repair resin.
2. Easy handling. Controlled hardening.

How does MD UV-STAR work?
1. UV-STAR is a radiation-hardening liquid plastic originating from industrial and medical development.
2. UV reactive photo initiators react in a liquid plastic matrix to external UV exposure and determine the hardening
reaction.
3. The intensity of UV radiation determines both hardness and elasticity as well as the reaction rate.

What can MD UV-STAR be used for?
1. Applicable to virtually any materials e.g. glass, metal, plastic, stone, ceramic, wood, acrlyic etc.
2. For bonding, filling, locking, waterproofing, sealing, insulating, modelling.
3. Fill and seal cracks in surfaces such as glass, vases, rubber products, metal containers etc.
4. Insulation, sealing and grouting of electrical components such as boards, low voltage components etc.
5. Remodelling of material defects - can be sanded, is drillable and paintable.
6. Fix, connect and secure during the entire model building process. Selectively within seconds and with the push of a button.
7. Glass and stone chip repairs for the automotive sector.
8. As a seam sealer in the textile and outdoor markets such as tent fabrics, hoses and rubber products.
9. As a 3-D modelling medium for arts and crafts such as crystal, glass creations, mosaics, miniature sculptures and jewellery making.

Working Tips
1. Adhesive surfaces should be sound, rust-and corrosion-free and as free from paint and separating layers as possible.
2. Bond surfaces should exhibit a significant surface roughness. For this purpose, smooth surfaces should possibly be sanded (K80-180).
3. For optimal results bond surfaces should be dry, clean, dust and grease free. For this purpose isopropanol, acetone, thinner and soap / silicone-free non-greasy cleaners are suitable.
4. Adhesion should best be carried out so that the main surface is perpendicular to the bonding load (tensile load). Buckling, shearing and torsional forces in the adhesive joint should be avoided.
5. The minimum bond gap should be 0.05-0.15 mm. Large bond gaps or holes should be covered by layered application. Maximum layer thickness should not exceed 2 mm per layer.
6. The adhesive reacts within 1-3 seconds. Ideally, adhesive bonds should initially be fixed at points and then reworked
thicker (without tension or pressure forces).
7. For a fast and complete hardening reaction the distance of the UV-LED to the adhesive surface should be as close as
 possible.
8. The adhesive reacts for up to 24 hours post hardening, due to UV radiation in ambient light as well as in daylight.
9. After hardening, the adhesive surface can be machined (drilling, sawing, grinding) be painted.
10. The adhesive reacts only in areas accessible to light. Excess material and adhesive contamination should be removed immediately with isopropanol / acetone such as nail polish remover.
11. Not suitable for glass with UV filter.

Instructions for use:
Adhesive surfaces have to be dry, dust and grease free. Surfaces should be roughened. To open, cut the point by 2 mm. Apply adhesive thinly and to one side. Push the parts to be bonded together align and correct. Thereafter fix together without pressure and light with the UV projector for 3-30 seconds. Use the UV-STAR UV projector or a commercially available UV lamp with an object distance of 1-10 mm. If possible leave the bond to rest undisturbed for a few minutes. 50% strength after 3 seconds, 90% strength after about 30 sec, final strength after 1-24 hours. The adhesive reacts to UV exposure even in daylight. Indoor and outdoor weather resistant use. Store the bottle upright in cool and dark surroundings. Cover dosing point during work breaks.

 MD MS Polymer

is a high-quality MS POLYMER-based adhesive

•     Isocyanate and silicone-free
•     Can be painted over or coated
•     Permanently elastic
•     Applicable wet-on-wet
•     Resistant to UV radiation, weather, salt water and chlorine
•     Excellent adhesion on many surfaces
•     Rapid hardening
•     Available in white, black, grey and transparent
•     Temperature-resistant from -40 to +100°C
•     (+130°C possible for short periods of 2-3 hours -
      except transparent)
•     Processing temperature +5 to +40°C

Areas of application:
Gluing metals, wood and plastics together and to each other in container construction, metalworking, apparatus engineering, air conditioning, yacht/boatbuilding, bodywork and vehicle construction, the elastic sealing of grooves and seams in areas where silicone cannot be used. (Silicone contamination when painting)

Packaging:
Art.-No. MMS.K290, grey/MMS.K290-W, white/MMS.K290-S, black - unit 20 cartridges á 440 g    
Art.-No. MMS.K290-T, clear - unit 20 cartridges á 300 g
Art.-No. MMS.W.T60, white - unit 10 tubes à 120 g

MD MS Polymer SPRAYABLE

is sprayable sealant and seam sealer in one. Sprayable seam sealer for overlapping plates and welds in the original structure. Good adhesion to metals (zinc, aluminum, steel), primed and painted metal, wood materials, many duro-and thermoplastics. MD-MS Polymer sprayable adheres to most substrates without priming and primer

A product for two applications

• Sound inhibitory effect
• Solvent, isocyanate and silicone-free
• Very good UV-resistance and aging stability
• Spray and spreadable
• Painted over immediately (wet-on-wet)
• Permanently elastic after curing
• Minimize the formation of cracks in the paint
• Improved stone guard
• Resistant to mechanical damage
• Rapid skin formation
• Vibration absorption
• Silicone and isocyanates
• Be spot welded in an uncured state

With a fast painting over the curing is not prevented but delayed.

Packacking:
Art.No.: MMS.G.S450 - Unit 12 cartridges á 450 g  

MD MS 2K Polymer  

•  Rapid hardening due to 2 K system
•  Hardening without humidity even with large surfaces
•  Isocyanate and silicone-free
•  Can be painted over or coated
•  Permanently elastic
•  Applicable wet-on-wet

Resistant to UV, weather, water, damp and chlorine. MD MS 2K Polymer adheres extremely well to many surfaces in most cases without primer. Its temperature resistance range is between -40°C and +90°C. Shore A Hardness 40 DIN 53505.
Complete hardening after four hours – conventional MS Polymer (3 mm) in 24 hours. Handling with standard silicone guns.

Packaging: Art.-No. MMS.2K.G unit 12 cartridges á 400 g | MMS.2K.G.S400 unit 12 double cartridges á 500 g